Table of Contents

Natural Convective Vertical Boundary Layer

Experiments by Tsuji and Nagano


Description

Turbulent natural convective boundary layer along a vertical heated copper plate. 2D incompressible air flow with temperature and density variation.

Experimental Arrangement

The experimental arrangement is shown in figure 1. The boundary layer develops over the 1m wide by 4m long flat plate, which is heated via a series of steel strip heaters, controlled in such a way to produce a constant plate surface temperature.

 Experimental arrangementFig. 1: Experimental arrangement

Velocity and temperature measurements are provided at four locations along the plate: 1.44 m, 1.92 m, 2.54 m and 3.24 m from the leading edge.

Flow Characteristics

Turbulence in this kind of flow is driven by buoyancy forces in such a way that relatively large fluctuations of velocity and temperature take place at low velocity.

The copper plate generating the flow is 4 m long and 1 m wide. It is suspended in a sufficiently large room. The leading edge of the plate is chamfered in order to allow a stable laminar boundary layer to develop. Two-dimensionality is ensured by side boards on both sides of the plate. The surface is heated to a constant temperature, and the boundary layer becomes naturally turbulent at about \(x = 0.8\) m above the leading edge.

Flow Parameters

Inflow Conditions

Simulations of the flow could be started from the leading edge of the plate, with uniform ambient conditions, in order to capture the entire boundary layer development, including transition.

For those wishing to start calculations further downstream, the measurements at \(x=1.44\) m could be used to represent the partially developed turbulent boundary layer there. Data at this location (stored in files nw_bl004.dat and nw_bl007.dat) include:

Experimental Details

Fluid temperature and velocity have been measured using a normal hot wire coupled to a cold wire. Several measurements have been carried out at nearly the same locations but with different Grashof numbers.

Fluid temperature close to the wall has been measured using a platinum-rhodium-platinum thermocouple up to \(y^+ = 4\).

Ambient temperature \(T_a\) has been measured using seven thermocouples placed 600 mm away from the heated surface.

Surface temperature \(T_w\) has been measured using copper-constantan thermocouples embedded in the back of the vertical plate.

The friction velocity is defined as: \(u_{\tau} = (\tau_w/\rho)^{1/2}\) where \(\tau_w\) is the wall shear stress.

The wall shear stress is obtained from \(\partial U/\partial y|_{y=0}\).

The friction temperature is defined as: \(t_{\tau} = q_w/\rho C_pU^*\) where \(C_p\) is the specific heat at constant pressure.

The wall heat flux is defined as: \(q_w = -\lambda_w(\partial\Theta/\partial y)_{y=0}\) and determined from the measured temperature gradient at the wall.

Measurement Errors:

\(\delta(y)\) \(\pm 0.13\) \(\delta(\Theta/t_{\tau})\) \(\pm 0.14\)
\(\delta(U/u_{\tau})\) \(\pm 0.14\) \(\delta(W/u_{\tau})\) \(\pm 0.24\)
\(\delta(u'/u_{\tau})\) \(\pm 0.04\) \(\delta(w'/u_{\tau})\) \(\pm 0.03\)
\(\delta(\overline{uw}/(u_{\tau})^2)\) \(\pm 0.08\) \(\delta((\overline{\theta^2})^{1/2}/t_{\tau})\) \(\pm 0.05\)
\(\delta(\overline{u\theta}/(t_{\tau}u_{\tau}))\) \(\pm 0.07\) \(\delta(\overline{w\theta}/(t_{\tau}u_{\tau}))\) \(\pm 0.05\)

Available Measurements

The data is stored in five files, which can be downloaded as compressed archives from the links below, or as individual files.

Sample plots of selected quantities are available.

Nusselt Number and Wall Shear Stress

Part of the data in file nw_bl004.dat represents:

Profiles Across the Boundary Layer

Stored in files nw_bl004.dat and nw_bl007.dat are profiles across the boundary layer, at four locations (\(x=1.438\), \(1.918\), \(2.535\) and \(3.264\) m, corresponding to \(Gr_x=1.55\times 10^{10}\), \(3.62\times 10^{10}\), \(8.44\times 10^{10}\) and \(1.80\times 10^{11}\)) of:

Stored in file nw_bl006.dat are profiles at \(x = 2.538\) m (\(Gr_x = 7.99\times 10^10\) and \(T_w - T_a = 41.4\)oC) of:

Stored in file nw_bl005.dat are profiles at \(x=2.536\) m (\(Gr_x = 8.99\times 10^10\) and \(T_w - T_a = 45.3\)oC) of:

Stored in file nw_bl008.dat are profiles at \(x=2.536\) m (\(Gr_x = 8.99\times 10^10\) and \(T_w - T_a = 45.3\)oC) of:

Recommendations for Calculations

The following suggestions were given to contributors to a collaborative workshop in which the case was studied.

Type of Calculation: Two different types of calculation can be chosen, considering either the parabolic or the elliptic problem.

Inlet Conditions: The calculation of the boundary layer could be started at \(x = 1.44\) m using the experimental values provided as inlet conditions. These values correspond to a partially developed turbulent natural convective boundary layer. Alternatively the flow development over the whole plate length could be modelled, including the transition of the boundary layer.

Heated Wall: Surface heated at a constant uniform temperature: \(T_w\).

Entrainment Boundary: For elliptic calculations, the entrainment boundary should be placed rather far away from the heated wall, typically \(y ge 500\) mm. According to the measurements there is a slight inflow in the \(-y\) direction. One should then prescribe inflow conditions as \(U=0\), \(V < 0 \), \(p=p_a\), \(\Theta =T_a\) and low values for the turbulent quantities. \(U\) and \(p\) are known, \(V\) may be computed by solving the \(y\)-momentum equation at the boundary.

Outlet Conditions: Zero gradients in \(x\) direction for the flow variables may be prescribed. If necessary, this boundary might be moved farther away in the \(x\) direction .

Previous Numerical Studies

Kato et al. (1993) used an elliptic method to calculate the turbulent boundary layer for \(T_w - T_a = 43\)oC and \(404\)oC using three different \(k\)-\(\varepsilon\) turbulence models. They all include correction terms for treating the near-wall low-Re flow. The first one uses ensemble averages and variable density. The second one uses Favre averages and variable density also. The last one uses ensemble averages and Boussinesq's approximation for incompressible flows. The authors have compared their profiles of velocities, temperature and velocity-temperature correlations with the experimental ones at \(x = 1.90\) m (\(Gr_x = 4.5\times 10^10\) and \(T_w - T_a = 43\)oC). The authors state that “the correspondence between the experiments and the present three numerical models is fairly good”. However, the first model gives slightly better results. To summarize, they fail only in predicting the \(\overline{\theta^2}\) profiles, they slightly underpredict \(\overline{u^2}\) and overpredict \(\overline{v^2}\) profiles and fully succeed in predicting \(U\), \(T\), \(\overline{uv}\) and \(\overline{v\theta}\) profiles.

Main References

Description of experiments

  1. Tsuji, T., Nagano, Y. (1988). Characteristics of a turbulent natural convection boundary layer along a vertical flat plate. Int. J. Heat Mass Transfer, Vol. 31, pp. 1723-1734.
  2. Tsuji, T., Nagano, Y. (1988). Turbulence measurements in a natural convection boundary layer along a vertical flat plate. Int. J. Heat Mass Transfer, Vol. 31, pp. 2101-2111.
  3. Nagano, Y., Tagawa, M., Tsuji, T. (1991). Thermally driven turbulent boundary layer. 8th Int. Symp. on Turbulent Shear Flows, Munich.

Previous numerical calculations

  1. Kato, S., Murakami, S., Yoshie, R. (1993). Experimental and numerical study on natural convection with strong density variation along a heated vertical plate. Proc. 9th Int. Symp on Turbulent Shear Flows, Kyoto, Japan.
  2. Henkes, R.A.W.M., Hoogendoorn, C.J. (1989). Comparison of turbulence models for the natural convection boundary layer along a heated vertical plate. Int. J. Heat Mass Transfer, Vol.32, p.157.
  3. George, W.K., Capp S.P. (1979). A theory for natural convection turbulent boundary layers next to heated vertical surfaces. Int. J. Heat Mass Transfer, Vol.22, p.813.
  4. To, W.M., Humphrey, J.A.C. (1986). Numerical simulation of buoyant, turbulent flow-I. free convection along a heated, vertical flat plate. Int. J. Heat Mass Transfer, Vol.29, p.573.

Indexed data:

case009 (dbcase, semi_confined_flow)
case009
titleNatural Convection Boundary Layer
authorTsuji, Nagano
year1987
typeEXP
flow_tag2, scalar, buoyant, 2dbl